Calculator FDM 3D printing
3D print time and cost calculator
Drop an STL or 3MF and get the print time, filament length and weight, and what the print costs, without opening a slicer. The model is sliced layer by layer in your browser, so the estimate follows its real geometry, not just its volume.
01 Method
How the print time is calculated
Volume-based calculators divide the part’s volume by a flow rate. That misses most of what sets the time: walls are printed slowly, small layers wait for cooling, and every corner forces the nozzle to slow down. This calculator does what a slicer does instead:
- Slices every layerThe mesh is cut at each layer height into closed outlines. Walls (perimeters) follow those outlines; the inside is split into solid top and bottom skins and sparse infill.
- Plans the moves like printer firmwareEach wall is planned with acceleration, corner speeds (junction deviation) and look-ahead, so a small detailed part takes longer than a smooth one of the same volume.
- Adds what slicers addInfill lines and anchors, supports under overhangs past 45° (not under bridges), travel moves, retractions, layer changes and the minimum layer time for small layers.
02 Accuracy
Checked against PrusaSlicer
We sliced the same parts in PrusaSlicer 2.9.2 with identical settings and compared its prediction with ours.
| Part | Print time | Filament |
|---|---|---|
| Bracket | −2.8 % | +2.3 % |
| Spur gear | −4.2 % | +0.8 % |
| 3MF sample, two profiles | −1 to −3 % | +1 to +3 % |
| Tee with supports | −4.6 % | +2.5 % |
| Sphere | −1.5 % | +1.4 % |
| Table with bridges | −10 % | −6.5 % |
Not modelled: skirt and brim, ironing, gap fill, bridge flow, variable layer height and heat-up time. Real printers also differ from any slicer’s prediction, typically by a few percent.
03 Pricing a print
How to work out what a 3D print costs
A useful price for an FDM print has three parts:
- Filament: grams used × price per kilogram ÷ 1000. A 1 kg spool of PLA at 20 makes 0.02 per gram.
- Machine time: hours × an hourly rate that covers electricity, wear and the printer’s cost spread over its life. Hobby printers come to roughly 0.5 to 2 per hour; print services often charge 2 to 10 per hour, including labour.
- Fixed costs per job: setup, removing the part and supports, packing. Add a margin on top if you sell prints.
Enter your own rates in the calculator above; the result updates as you type.
04 FAQ
Questions and answers
How accurate is this 3D print time estimate?
With the same settings it came within about 5 % of PrusaSlicer 2.9.2 on most test parts, usually slightly lower. Parts with long bridges come out about 10 % low. The estimate is for a printer that reaches the configured speeds and acceleration; a slower printer takes longer.
Is my file uploaded?
No. The slicer is a WebAssembly module that runs in your browser tab. The file is read from your disk into the page and never sent anywhere.
Does it use the settings saved in my 3MF?
Yes. 3MF projects from PrusaSlicer, Bambu Studio and OrcaSlicer store their print profile, and the calculator starts from it: layer height, infill, walls, supports, speeds and filament. If a Bambu Studio or OrcaSlicer project was already sliced, the slicer’s own time prediction is shown next to ours.
Why is the print time longer than the volume suggests?
Most of the time goes into walls and solid skins, which are printed slowly, and into slowing down at corners. Small layers also have to wait for a minimum layer time so the plastic can cool. That is why a detailed part can take twice as long as a smooth block of the same volume.
How much filament does a print use?
The calculator adds up the plastic in every wall, skin, infill line and support line and converts it to length and weight for 1.75 mm filament. Weight depends on the material: PLA is about 1.24 g/cm³, PETG 1.27, ABS 1.04.
Can I get this estimate from my own software?
Yes. POST /v1/analyze?print=1 returns the same estimate as JSON, with settings in print_settings= and the filament in material=. It costs one unit, so a quote with a thumbnail is two; the free plan includes 100 units a month. See the API docs.
Quote every upload automatically
Building a 3D-print quoting plug-in, a print farm or a marketplace? One API call returns print time, filament and supports, plus a thumbnail for the cart. EU-hosted, published prices.
More free tools: STL volume and weight · laser cutting cost from DXF · 3MF preview · STL to PNG · 3D viewer